Information on our Flow Measurements:

AW FLOW METERS - Positive Displacement Flow meters-

Why use a PD meter?

Designed to maintain accuracy despite the liquids changing viscosity conditions
No straight run required
Well suited for measurement of oil, grease, fuel, solvents, polyurethanes, brake fluid, paints, adhesives, sealants, and resins
Provide electronics for ratio control and batch along with flow and total

Smart Measurement

offers the Micro-Bend Coriolis Meter ,Delta-Tubed Coriolis Meter ,U-Tubed Coriolis Meter

What is it, and why should I consider using?

The meter consists of tubes vibrating at a specific frequency. A bend or twist occurs when fluid flows through the tube. This twist is measured according to Newton's Second Law of Motion. The amount of sensor tube twist is directly proportional to the mass flow rate of fluid flowing through the tube.
Coriolis contains no moving parts to be replaced
No need to recalibrate for different process fluids
Provides mass flow, density, temperature, and volumetric flow
Price is right at less than $3000 up to flows of 13.5 GPM or 50,000 gram

EASTECH FLOW CONTROLS - Ultrasonic meters-

Why should I consider using these flow meter products?

The VANTAGE 2200 generates and reads sound waves that are being bounced off of a fluid in an open channel, and based on the configuration of the channel (flume, weir, or flow nozzles) will provide the Influent or Effluent flow and total flow.

The VANTAGE 3000 and 4000 are transit time flow meters that measure the time difference in two ultrasonic sensor signals and utilizes a phase-shift detection system that enhances the accuracy of the readings. The VANTAGE 3000 is for continuous on-line, and the VANTAGE 4000 is for portable use.

The ACCURON 7100, 7200 and 7400 are designed to measure flow in pipes where the flow is only partial, up to submerged flow or flow in an open sewer during a storm event or blockage in a line

Advantages of this technology?

No moving parts to measure flow in an open channel
VANTAGE 3000 and 4000 do not need to penetrate into the pipe for flow measurements
Partially filled pipes and very low flows (ACCURON 7100, 7200 AND 7400)
Easy installation versus the conventional flume
VANTAGE 4000 provides a means of portable measuring flows in sealed pipes

McCROMETER - V-CONE® Meter

Why use a V-CONE® meter?

No straight run required
Turn down can be as good as 20 to one inflow
Linear signal down to 7000 Reynolds numbers and repeatable to 500 Reynolds number
Can always be built longer than the design if you have a flanged pipe section so as to avoid extra welding and cutting
The V-Cone forces the liquid into a flat flow profile, and the sensing ports will stay clean.
The V-Cone can be mounted right after an elbow without any loss of accuracy
The V-Cone will accurately provide a steady signal down to .1 inch WC differential
The V-Cone can be built from 1/2 inch in size to any larger pipe size that you need

V-Cone "Seeing is Believing" Video- McCrometer's V-Cone conditioning effect removes swirl and potential metering uncertainty.

Click below to watch the video.

McCROMETER – 395L FPI (Full Pipe Insertion)

Click on the picture to see the 395L FPI installation and how the sensor measures flow

A Multiple measuring point meter that can be used for:

Potable and chilled water from line sizes of 6 to 120 inches
Installation is a hot tap insertion, and with multiple sensors on one bar, spans the entire pipe and compensates for shifting profiles providing a 1% accuracy.
Streamline sensor shape minimizes flow disturbances and provides minimal pressure drop.

McCROMETER – Insertion Mag Meter Model 282L SPI (Single Pipe Insertion)

A single Mag meter Insertion sensor can be used to measure flow in:

Waste Water and Water, Industrial flow processes, pulp stock, chemical laden flow
The sensor can provide excellent accuracy because of the profiling of the flow on site.
The hot tap installation makes this an economical solution on large pipes but also smaller pipe installation saves time and piping changes
The Model 282L can be used from line sizes 4 to 96 inches.

RONAN - RLL Belt Weighing & Plug Chute detection

Arlyn Scales

Arlyn Scales, with the Surface Acoustic Wave Technology having a resolution of .002pound on a 200-pound scale, can provide you with 1/5 of 1% accuracy in measuring the mass of product being transferred. Click on "Arlyn Scales" and learn more about the new technology offering 10times the accuracy of standard load cells.

Information on our Flow Measurements:

This website uses cookies.